Differences
This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
wiki:tcb:operation:functionlist [2019/04/23 22:55] opadmin [Cannon and Related Functions] |
wiki:tcb:operation:functionlist [2021/03/22 23:43] opadmin [General Purpose Outputs A & B] |
||
---|---|---|---|
Line 172: | Line 172: | ||
===User Sound (1..12) - Play once | Repeat | Stop (D)=== | ===User Sound (1..12) - Play once | Repeat | Stop (D)=== | ||
**Play once**: Play the selected User Sound once. **Repeat**: Start playing the selected User Sound and keep repeating it until the Stop function is called. **Stop**: Use this to stop playing the selected User Sound after you started repeating it. | **Play once**: Play the selected User Sound once. **Repeat**: Start playing the selected User Sound and keep repeating it until the Stop function is called. **Stop**: Use this to stop playing the selected User Sound after you started repeating it. | ||
+ | |||
+ | ===User Sounds - Stop All (D)=== | ||
+ | Will stop any user sound currently playing. | ||
===Sound Bank A/B - Play/Stop (D)=== | ===Sound Bank A/B - Play/Stop (D)=== | ||
Line 207: | Line 210: | ||
===External Output A | B - On | Off | Toggle | Pulse | Blink (D)=== | ===External Output A | B - On | Off | Toggle | Pulse | Blink (D)=== | ||
- | The **On** function will turn Output A on, the **Off** function will turn it off, and the **Toggle** function will toggle the Output A status (on → off, off → on). The **Pulse** function will briefly set the pin to the opposite state of its default level (default level set in OP Config, either High or Low). Use the Pulse function to emulate a button press to some external device. The **Blink** function will start blinking the output at the rate specified on the [[wiki: | + | The **On** function will turn Output A on, the **Off** function will turn it off, and the **Toggle** function will toggle the Output A status (on → off, off → on). The **Pulse** function will briefly set the pin to the opposite state of its default level (default level set in OP Config, either High or Low). The pulse length can be specified on the [[wiki: |
\\ | \\ | ||
Line 218: | Line 221: | ||
===Smoker - Enable | Disable | Toggle (D)=== | ===Smoker - Enable | Disable | Toggle (D)=== | ||
These three functions are only available if the **Smoker Control** setting is set to **Auto (with engine speed)** on the [[wiki: | These three functions are only available if the **Smoker Control** setting is set to **Auto (with engine speed)** on the [[wiki: | ||
+ | |||
+ | ===Smoker Preheat - Enable | Disable | Toggle (D)=== | ||
+ | If you are using a smoker type that involves separate control of the heating element and fan, you will also be given the option to specify a preheat time (see the [[wiki: | ||
===Smoker - Manual Speed (A)=== | ===Smoker - Manual Speed (A)=== | ||
Almost everyone will want to have the smoker controlled automatically by the TCB to reflect engine speed. But if you are not using a smoker and would like a general purpose, unidirectional speed control rated at 3 amps, or for some reason you just want to control the smoker manually, change the **Smoker Control** setting to **Manual** on the [[wiki: | Almost everyone will want to have the smoker controlled automatically by the TCB to reflect engine speed. But if you are not using a smoker and would like a general purpose, unidirectional speed control rated at 3 amps, or for some reason you just want to control the smoker manually, change the **Smoker Control** setting to **Manual** on the [[wiki: | ||
- | ===Smoker - Manual On | Off (D)=== | + | ===Smoker - Manual On | Off | Toggle |
- | Almost everyone will want to have the smoker controlled automatically by the TCB to reflect engine speed. But if you are not using a smoker and would like a general purpose, high current capable digital switch, then change the **Smoker Control** setting to **Manual** on the [[wiki: | + | Almost everyone will want to have the smoker controlled automatically by the TCB to reflect engine speed. But if you are not using a smoker and would like a general purpose, high current capable digital switch, then change the **Smoker Control** setting to **Manual** on the [[wiki: |
Line 260: | Line 266: | ||
===RC Output 1-4, 6-8 - Pass-through (A)=== | ===RC Output 1-4, 6-8 - Pass-through (A)=== | ||
- | If available, these functions will appear in the function list. Assign an analog trigger | + | If available, these functions will appear in the function list. Assign an analog trigger to control any servo or ESC plugged into the corresponding RC Output. |
+ | **Note:** even if the physical control on your radio is a switch, you should set its Aux channel to " | ||
+ | **Note: | ||
===RC Output 1-4, 6-8 - Pan Servo (A)=== | ===RC Output 1-4, 6-8 - Pan Servo (A)=== |