This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Messages - thegreen
1
« on: May 31, 2022, 09:10:29 PM »
ok found my problem; The battery voltage monitor was reading from the regulated 5V not from the battery; change the wire; solved!
2
« on: May 31, 2022, 06:47:05 PM »
Hi,
I have two TCB, one working with my other radiomaster with frsky receiver (that one work fine) and the other one with radiomaster receiver (the one that is bad) (TCB version made with arduino stock board mega2560). with the good TCB all my receivers are working fine with the controller near or not. It is the other TCB that have that strange problem. I have compared my two circuit and they are the same. I may have shorted or damaged the serial RX3. It is possible to change the firmware to use the unnused RX2?
3
« on: May 30, 2022, 04:39:05 PM »
Hi,
If the red and green led flash alternately and rapidly for 2 second and after slowly flashing is it a radio lost signal?
5
« on: May 14, 2022, 05:50:23 PM »
its really nice what you said but i am not the désigner ! I dont have the patience and the program to do that! i get the files at 3dprintedtanks.com. that Guy have designed some tanks. the price of the files are low for the quality of the parts. the manual is perfect, like a tamya. they take long time to assemble but are easy to print and if your printer is calibrated you will have very few corrections to do
6
« on: May 14, 2022, 06:37:15 AM »
hi and thank you very much ! I print them with a simple creality ender pro! i put some modification like linear rail put the calibration is what really make the différence. I have to put photos of the sherman of my son. i have almost finished the two board. I have use version with arduino. they will have most of the option with IR combat. One of them is finished and working fine. i have put taigen sound card. really nice print
7
« on: February 14, 2022, 09:31:03 PM »
other photos
8
« on: February 14, 2022, 09:27:44 PM »
here are some photos of the project. that thing is huge!!! 5kg of PLA! about 700mm long!
9
« on: February 14, 2022, 12:14:43 PM »
haha merci Luke effectivement tu viens de la France!
Otherwise thanks for the info about the member project. I will mainly use the picture that you put in an ancient post about using arduino because I use 2 external esc and also Sbus reveiver. i will also install IR. about that; you really make the current rise to 2 to 3A with a 3ohms resistor and a .8A transistor without blowing it?? I will get a 4A transistor just to be sure. what is the range with that setup?
10
« on: February 09, 2022, 09:51:25 PM »
i have finished assembly! i need to put electronic. the assembly of the tcb was ok except that there is no good atmega and i didnt find the right usb/uart IC... i will put that aside and build the other version with the arduino. i have already one. more easy to assemble. when electronic part will become disponible i will finish the tcb to put it in another tank!
11
« on: January 05, 2022, 09:56:35 AM »
Hi,
did you try the atmega from alliexpress? There is some that seem to be ok. Did some people have good experience with these chip and from wich seller?
12
« on: November 25, 2021, 06:58:11 AM »
other photos
13
« on: November 25, 2021, 06:56:37 AM »
i have ordered my pcb. the great fun will begin soon!
14
« on: November 25, 2021, 06:54:56 AM »
these project are so easy to print and built ! its really like a tamiya kit.
15
« on: November 11, 2021, 02:45:47 PM »
when you talk about assembling the tcb is there common problem or if I follow the drawing everything should be ok? ( in the case that my assembly is good)
|
Show Posts