This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
Messages - jhamm
Pages: 1 2 [3] 4 5 6 ... 10
31
« on: November 20, 2020, 03:40:33 AM »
This is the Main Processing Unit. it can get warm - but not hot! If it gets hot there is a problem with the power supply or there is a short circuit somewhere and an increased current is flowing. With all due respect - I think that you are not able to determine that ...
32
« on: October 27, 2020, 04:52:24 AM »
....this is really easy and not rocket science.
34
« on: August 03, 2020, 01:15:35 PM »
Before you waste more money on these cheap esc better spend a little more money and buy Hobbywing quicrun wp 1080.
35
« on: August 02, 2020, 12:55:52 AM »
It coult be a fault Motor. Did you swap the Motors from left to right side?
36
« on: June 05, 2020, 07:27:37 AM »
Hi, it is possible to wire one LED direct to the Arduino lights output. A little transistor or FET is neccessary if the current for the lights is higher than 30 -50 mA.
37
« on: May 27, 2020, 08:38:29 AM »
Nothing has been written here for 7 days ... Is there no longer a TCB user?
38
« on: May 12, 2020, 03:26:23 AM »
Hey Jerry, I do that some years ago. link the Potentiometer Shaft with a short piece of tube on a little Servo and glue together with a strip of plastic.
Thank you for the Files.
39
« on: May 07, 2020, 03:29:46 PM »
Turn the motor of recoilunit in right direction?
40
« on: April 24, 2020, 02:45:37 PM »
Hi Jerry, i use the cheap Mega2560 Pro Mini R3. But i desolder the Voltage-Regulator because it deliver only 1000mA - this ist not enough for the TCB. I use a little external circuit with LT1085CT = 3A or LT1084 = 5A for Tanks with a lot of Lights.
41
« on: March 10, 2020, 01:55:58 PM »
Hi, the only way to have the barrel sound with the gyro is a solution looped into the SBUS between the receiver and the TCB. There is the S6R and S8R from FrSky - receiver with built in 3-axis stabilization. But this reciever cost arround 40,- or 50,-€ and you cannot set anything... The StabiWII cost half of them and have a lot more features and is better to configure/parameterize.
42
« on: January 25, 2020, 06:42:41 AM »
Look excellent!
44
« on: November 30, 2019, 03:20:06 AM »
My opinion is, for the hobby i use and buy the best i can get. The TCB is in my eyes the best Solution.
45
« on: November 29, 2019, 12:28:54 AM »
Hi there, Luke thank you for the pictures...
Wibbly, I think you put yourself big stones in the way. Try the simple things first and buy a iBus or SBus RX - it could not be easier. All RC-Output at the TCB works perfect - there is no hassle. Have a look at the 5V voltage, the 2560 board has a voltage regulator with 1A performance - that is not much. For more than one servo you need extra 5V. Look at the Picture, there is a 5V 3A voltage regulator.
DasMicro can not be louder or better than a TCB Mini, it only has a 1W amplifier. Important: You need an 8 ohm speaker with good efficiency like Visaton FRWS-5 If the sound sample is recorded too loud, you get distortion.
Pages: 1 2 [3] 4 5 6 ... 10
|