16

Open Panzer Help / Re: second board overheating??

« on: December 07, 2020, 10:44:50 PM »

Okay somewhat figured it out! The second board was overheating only because the TBS plugs were not always in the right connections..one cable was
one pin up to high! The first board the main processor per your thoughts is shorted but I cannot find anything wrong with a glass...and that board stays hot all the time and all functions not working now. BUT the other ones are fine and that is a good thing..the TBS pins to be careful of for sure. Thanks..

17

Open Panzer Help / Re: second board overheating??

« on: December 06, 2020, 12:19:50 PM »

oddly it then stopped overheating and shutting down after letting it sit for a while and so far not doing it again.
I hope it will continue to function properly..such a great design I just fear Hobby
King did not do a great job perhaps on execution. Thanks

18

Open Panzer Help / second board overheating??

« on: December 06, 2020, 11:15:31 AM »

My second board was working fine but now overheating and it happens when detached from anything..ie. nothing external
touching anything on the board. Is there anybody on the forum who could possibly try fixing it if it was mailed to them?
Just discouraging as it was working fine but clearly something shorted out.

19

Open Panzer Help / Re: 2nd machine gun

« on: November 26, 2020, 11:25:16 AM »

Okay I see it on the wiki..it is triggered in that slot! So I would need to swap sounds out to do that. Just wish there were a
few more customizable user sounds slots ..but all good! Thanks for the quick response.

20

Open Panzer Help / Re: 2nd machine gun

« on: November 26, 2020, 10:05:23 AM »

Right.. on the Benedini the 3rd sound row after the engine is for cannon and the 4th for MG.
But the 2nd machine gun is that designated with a slot? It played sound from user sound 3
(row 11) which I had another type of sound in. Not a big issue just curious. Ty!

21

Open Panzer Help / 2nd machine gun

« on: November 25, 2020, 09:53:49 PM »

Is there a way to add a second sound to the 2nd machine gun or will it auto trigger the primary machine gun sound?

22

Open Panzer Help / Re: Hot area on board

« on: November 23, 2020, 07:06:09 PM »

Thanks...I was sure I would not be able to determine anything! I just
thought no way it should get hot like this. Though it does work with all
functions albeit some thing things do not always work properly all the time
but not sure if that is the issue. Luckily I have two other boards now

23

Open Panzer Help / Hot area on board

« on: November 19, 2020, 07:46:26 PM »

Was lucky to acquire two more boards..now 3 in total! Two from England and one from Poland

My first board gets very hot in the area indicated in red. I didn't think this is supposed to happen
and the other ones only get mildly warm. The "hot" board seems to work well but sometimes
things do act quirky..ie. certain functions trigger other times they take a few tries.
Not a huge issue but curious if anybody had this area get very hot or perhaps knows what it could be
and if it could cause the board to act a little wonky?

Thanks!

24

Open Panzer Help / Re: Recoil wiring

« on: October 27, 2020, 10:44:56 AM »

Very simple..works. Just wired up according to that schematic you sent and works
fine on mechanical recoil setting. Thanks!

25

Open Panzer Help / Re: Recoil wiring

« on: October 27, 2020, 10:30:21 AM »

Thanks Luke,

What happens differently (or nothing) to the recoil
3 pin out puts as labeled on the bottom of the TCB (pos neg and signal) when switched from
Mechanical recoil to Airsoft?

26

Open Panzer Help / Re: Recoil wiring

« on: October 26, 2020, 11:32:46 PM »

Yes old Heng Long recoil unit in Stug that had High Intensity flash..then fitted Led that was triggered by BARC and recoil was triggered with TBS but now trying to wire it using TCB

27

Open Panzer Help / Re: Recoil wiring

« on: October 26, 2020, 07:33:29 AM »

My unit has a flash not airsoft but will look as the mechanism may be more similar or the same as what this is. Thanks!

28

Open Panzer Help / Re: Recoil wiring

« on: October 25, 2020, 10:55:28 PM »

Any suggestions?

29

Open Panzer Help / Re: Recoil wiring

« on: October 21, 2020, 11:40:57 PM »

Here is numbered diagram photo

30

Open Panzer Help / Recoil wiring

« on: October 21, 2020, 11:12:30 PM »

I wired my Taigen perfectly using the video and going to get a servo system for KT
but trying to fit Stug with recoil for TCB and slightly confused with this set up as to which wires
would be for positive / negative / signal  for the 3 pin plug?


In my diagram number #1  would be the positive to motor.

But unsure which of the others would be the negative and signal.

Any help appreciated