*

Offline larryzhou

  • 24
    • View Profile
  • Shanghai
1/6 Metalbox Luchs project
« on: February 06, 2019, 06:24:52 AM »
It is about time to share my build.

The project starts from Oct.2018, and I am performing weathering at the moment.
All the electronics are ready.
fuse box, TCB, Benedini TBSv2, Sabertooth 2*32, 2*APO esc, Henglong smoker unit

The systems will use 2*12v acid battery, the drive motors are 2*250 bushed motor.

However, I need to design an internal housing for all the electronics.

IMG_7891.jpg
1/6 Metalbox Luchs project IMG_7891.jpg
Views: 44
IMG_8030.JPG
1/6 Metalbox Luchs project IMG_8030.JPG
Views: 44
IMG_7902.jpg
1/6 Metalbox Luchs project IMG_7902.jpg
Views: 42
IMG_7906.jpg
1/6 Metalbox Luchs project IMG_7906.jpg
Views: 37
IMG_7923.jpg
1/6 Metalbox Luchs project IMG_7923.jpg
Views: 39
IMG_7924.jpg
1/6 Metalbox Luchs project IMG_7924.jpg
Views: 23
IMG_7925.jpg
1/6 Metalbox Luchs project IMG_7925.jpg
Views: 17
IMG_8003.jpg
1/6 Metalbox Luchs project IMG_8003.jpg
Views: 19

*

Offline larryzhou

  • 24
    • View Profile
  • Shanghai
Re: 1/6 Metalbox Luchs project
« Reply #1 on: February 06, 2019, 06:38:12 AM »
some results from this morning.....

IMG_8054.jpg
1/6 Metalbox Luchs project IMG_8054.jpg
Views: 23
IMG_8057.jpg
1/6 Metalbox Luchs project IMG_8057.jpg
Views: 20
IMG_8060.jpg
1/6 Metalbox Luchs project IMG_8060.jpg
Views: 20
IMG_8063.JPG
1/6 Metalbox Luchs project IMG_8063.JPG
Views: 18
IMG_8066.jpg
1/6 Metalbox Luchs project IMG_8066.jpg
Views: 19

*

Offline johnnyvd

  • 145
    • View Profile
  • Netherlands
Re: 1/6 Metalbox Luchs project
« Reply #2 on: February 06, 2019, 01:49:33 PM »
Nice model you got there! 1/6 luchs! Full metal thank is it?

Found your thread on rcuniverse: http://www.rcuniverse.com/forum/rc-tanks-369/11658365-1st-thread-metalbox-1-6-panzer-luchs.html

Very nice!
* E-75 / E-100 PAK44 "monster" - in progress
* Sturmjagdtiger PAK44 - in progress
* pz.kpfw KV-2 754(r) - in progress
* T-34 88mm "Kurland Tiger" - in progress

*

Offline LukeZ

  • 626
    • View Profile
  • Kansas, USA
Re: 1/6 Metalbox Luchs project
« Reply #3 on: February 06, 2019, 06:38:51 PM »
I will follow along with interest, here and at RC Universe both. The early Panzers (I-II-III) are my favorites. Your weathering is looking very good.

I am curious about the "APO ESC" and the larger red board highlighted in this picture. Do you have links? I am always trying to learn about new products I haven't heard about before.
IMG_7891.jpg
1/6 Metalbox Luchs project IMG_7891.jpg
Views: 22
NO SUPPORT THROUGH PM - read why
Open Panzer FAQs

*

Offline larryzhou

  • 24
    • View Profile
  • Shanghai
Re: 1/6 Metalbox Luchs project
« Reply #4 on: February 06, 2019, 07:42:20 PM »
I will follow along with interest, here and at RC Universe both. The early Panzers (I-II-III) are my favorites. Your weathering is looking very good.

I am curious about the "APO ESC" and the larger red board highlighted in this picture. Do you have links? I am always trying to learn about new products I haven't heard about before.

ha,

the red board is an 2*60w AMP, tested by Thomas from Benedini, I guess my tank will be very loud and produces good quality sounds. I will  hook up 2* B&W speakers from my former car to it.

the APO esc is from a Chinese Robotistic company, delivers 120w each, which is more than capable to handle the elevation & turret rotation motors.

The big day is near, I will do the full test, with all the motors.

*

Offline LukeZ

  • 626
    • View Profile
  • Kansas, USA
Re: 1/6 Metalbox Luchs project
« Reply #5 on: February 06, 2019, 08:04:10 PM »
I found some APO speed controllers on AliExpress. It appears their main advantage over other options is their ability to handle moderate currents at high voltages. If someone was not running a 24 volt system, there probably would be more cost-effective solutions.

The Sabertooth 2x32 is a special case amongst the Sabertooth line, it uses a software provided by Dimension Engineering called DEScribe to alter settings. Let us know how it works for you.
NO SUPPORT THROUGH PM - read why
Open Panzer FAQs

*

Offline larryzhou

  • 24
    • View Profile
  • Shanghai
Re: 1/6 Metalbox Luchs project
« Reply #6 on: February 06, 2019, 08:39:04 PM »
I found some APO speed controllers on AliExpress. It appears their main advantage over other options is their ability to handle moderate currents at high voltages. If someone was not running a 24 volt system, there probably would be more cost-effective solutions.

The Sabertooth 2x32 is a special case amongst the Sabertooth line, it uses a software provided by Dimension Engineering called DEScribe to alter settings. Let us know how it works for you.

Hi Lukez

if you are building it, will you set Sabertooth 2*32 to independent mode, which leaves both motor's mixing to TCB?   or leave the mixing to Sabertooth?


Larry

*

Offline LukeZ

  • 626
    • View Profile
  • Kansas, USA
Re: 1/6 Metalbox Luchs project
« Reply #7 on: February 06, 2019, 08:46:54 PM »
You definitely want the TCB to do the mixing, set the Sabertooth to independent. TCB needs to control all that in order for turn modes, momentum/inertia and other effects to work properly.
NO SUPPORT THROUGH PM - read why
Open Panzer FAQs

*

Offline larryzhou

  • 24
    • View Profile
  • Shanghai
Re: 1/6 Metalbox Luchs project
« Reply #8 on: February 06, 2019, 09:25:52 PM »
You definitely want the TCB to do the mixing, set the Sabertooth to independent. TCB needs to control all that in order for turn modes, momentum/inertia and other effects to work properly.

yes, sir. crystal clear.

*

Offline larryzhou

  • 24
    • View Profile
  • Shanghai
Re: 1/6 Metalbox Luchs project
« Reply #9 on: February 09, 2019, 09:28:53 PM »
sabertooth tested & fitted to the chassis. Also, the ground terminal is screwed. next is the power distribution fuse box, and other wiring.
IMG_8197.jpg
(1710.84 kB ~ Downloads: 9)