Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Ja80

Pages: [1]
1
Open Panzer Help / Re: Assembling Boards by Hand
« on: December 10, 2017, 04:21:46 PM »
Good afternoon, in the end I did not manage to fix that table when releasing vnh2s with hot air was not enough heat and some pad was ripped so I discarded the table >:(. But the fourth was the good one. finally I have a functional scout.

2
Open Panzer Help / Re: Doubt last update and airsoft
« on: December 07, 2017, 04:16:00 PM »
how do you say the problem does not have to do with software that may be failing? the mosfet?

3
Open Panzer Help / Re: Assembling Boards by Hand
« on: December 07, 2017, 03:19:13 PM »
Do not worry, it just lacked that with the work you carry you had some responsibility. When I got into this mess I already knew what could happen. I will keep trying, I still have plates and some component, desoldering I will try to have air if I get it.

4
Open Panzer Help / Re: Assembling Boards by Hand
« on: December 07, 2017, 12:50:14 PM »
desisti of that table, try to mount another, this almost got it but I did not realize and I had two pins of a vnh2sp shorted and broke (smoke).    :'( :'(                  I have to change it if the rest still works

5
Open Panzer Help / Doubt last update and airsoft
« on: December 07, 2017, 12:42:11 PM »
Good afternoon, could it be that the last update blocked the function of firing the airsoft cannon? because I updated a new tcb that came to me and the one that was old and does not trigger me although in snoop if the function appears when I act on the trigger.

6
Open Panzer Help / Re: Assembling Boards by Hand
« on: November 22, 2017, 02:46:16 AM »
Good morning.
- Yes, I have connected the battery to the scout and this food tcb.
- E connected the scout to a standard receiver rc and only works the engine on one side.
the RC2 input works and the M1 motor works. (in one direction it works well and in the other it only turns slowly). E watched with the multimeter, without acting on the remote and the driver on the M1 side gives me a reading of 3v and the one on the M2 8v side. So I understand that the latter must be wrong. true?

7
Open Panzer Help / Re: Assembling Boards by Hand
« on: November 19, 2017, 01:05:44 PM »
Images

8
Open Panzer Help / Re: Assembling Boards by Hand
« on: November 19, 2017, 12:51:16 PM »
Good afternoon. First congratulate Luke for this great job. I ordered some scout pcb (rev.10) to seed, soldered the components with a hot plate as recommended. Burned the 328p atmega through the isp using an arduino nano and the arduino ide as (arduino as isp) then with the same arduino as cable ftdi and uploaded the program with open panzer. I think it went up well since it did not No error message. But a doubt arises when I connect the scout to the tcb by the serial port following the letters of the tcb and the scout (tx-rx- gnd) these are not in the same order on the two plates. as the plates mark, the red LED lights up intermittently and does not respond to any order of the control. but if I connect the cables in the same order as shown in the tcb, the blue led lights steadily, but does not respond to the movement of the stick, but if I move a wheel of the station to which I am assigned in a position the lights and in another cannon shot. When I put the firing position (if I have the airsoft gun disconnected) one of the engines moves a little towards a direction. If I have the gun connected it shoots and at the same time tries to move the engine but much less than if it is not connected and when this happens the blue led of the scout turns off and the red one turns on 4 times. I have to say that I do not have sbus or ibus station. if not a ppm adapter that transforms the signal from my standard receiver to ppm. the movement of the tower works and the lights on and off. if you can tell me if it's a problem with the station or the scout. a greeting sorry for the billet

Pages: [1]
bomber-explosion