Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Amaral

Pages: [1] 2
1
Open Panzer Help / Re: My tank lost some functions
« on: May 07, 2022, 01:32:56 AM »
Now it works!

Thx Luke for help.

2
Open Panzer Help / My tank lost some functions
« on: May 06, 2022, 03:00:27 PM »
Hi.
I have problem with my OP tcb in my Maus. It drives only backwards and neutral turn is possible only in left direction. If I want to go forward there is no acceleration sound. Moving backwards and neutral left turn arent proportional. Always full throttle. Position of stick doesnt matter.

When I plug tcb to pc I can see all stick movements in radio tab.

When snooping, tcb doesnt see driving forward.

Im trying to reflash - still problem.

So I took second op tcb, flashed from same config file and? Same problem!

So it isnt hardware problem?

3
Open Panzer Help / Re: IR Receiver doesnt work
« on: February 13, 2022, 01:57:50 PM »
Hi LukeZ. Thx for quick reply.

I set both to Tamiya protocol.

Im using TSOP4838 IR receivers - they work very good with clark board. With OP not :/ Can You recommend IR receiver model which works with OP?

Maybe I brake down Taigen apple when it wont work and then I plugged it in other way.

But my DIY receiver was plugged correctly I know.

4
Open Panzer Help / IR Receiver doesnt work
« on: February 13, 2022, 06:47:04 AM »
Hi.

I want to do some IR battling with my 8yr son. I have two tanks with Clark TK60 boards (one with Taigen Apple, second with hidden DIY system). I want IR system also in my Maus with OP TCB. So I made receiver like I did for Clark board. And it doesnt work :(

OP can send IR signal, LED shows cannon reloaded. But it doesnt receive any signal from other tanks or Clarks TV remote :( arghhhh.

Im very disappointed. Has anyone isssue like me?

Edit: taigen apple dead after plugging to OP :/

5
Show and Tell / Re: Asiatam FAMO SdKfz. 9
« on: May 06, 2018, 12:19:03 PM »
Congrats. Gr8 model here :) I like Famo's.

6
Show and Tell / Re: M1A2 Abrams (brushless)
« on: May 05, 2018, 04:30:00 PM »
Im here :)


7
Show and Tell / Re: M1A2 Abrams (brushless)
« on: May 05, 2018, 01:06:07 AM »
I have similar design of gearboxes :) But I see first time those from RCU.

My bevel gears are made from steel, not brass. I also added bearing on 6mm shaft on gear reductor for better stiffness.

I love brushless motors - so small and so much torque.

I also bought mine plow from DKLMRC. It will be motorized. I will connect motors to internal ESC


8
Show and Tell / M1A2 Abrams (brushless)
« on: May 04, 2018, 12:46:37 PM »
Hi! :)

Finally Abrams is alive. Sound is configured. Here is test video with 2s LiPo:



I printed gearboxes. Motors are 900kv with 1:30 reduction. I tested also with 3s LiPo and it has better speed.

Next stage will be brushless stabilization with Storm32 controller.

9
Open Panzer Help / Re: Big problem with TBS Mini
« on: April 22, 2018, 10:02:17 AM »
Finally it works. I reflashed TBS firmware. But I must using only sounds from Tomas.

Its no problem - in his TBS file there is cannon sound and crew sounds - thats all I want with engine sound.

I will post vid how it works.

Thx Luke for support.

10
Open Panzer Help / Re: Big problem with TBS Mini
« on: April 15, 2018, 02:57:36 PM »
Low voltage cutoff disabled. Now Snooping works fine. It shows User sounds.  So probably I must focus on TBS Mini.

I thought, voltage cutoff doesnt work when I program OP board.

Will send OPZ tomorrow if still needed

11
Open Panzer Help / Re: Big problem with TBS Mini
« on: April 15, 2018, 10:41:47 AM »
Yes. Of course

12
Open Panzer Help / Re: Big problem with TBS Mini
« on: April 15, 2018, 06:06:19 AM »
Update:

I flashed all files as .wave from hard disk. In MISC tab I can execute Engine start. When I execute Cannon Fire, I hear "click" sound. 3 user sounds dont work - I dont hear anything.

13
Open Panzer Help / Re: Big problem with TBS Mini
« on: April 15, 2018, 05:31:52 AM »
I think Snoop doesnt work.. Look at image attached. In Snoop mode I move sticks and nothing happen..

In the TBS Flash there is also problem. In MISC tab, executing sounds doesnt work too. Program doesnt respond.

I must have both TBS soundfile from Thomas and wave files for additional sounds. It will be easier to put all wav files from hard disk. But I dont have sounds for Abrams.

14
Open Panzer Help / Re: Big problem with TBS Mini
« on: April 14, 2018, 05:49:42 AM »
Yes. Wave 8bit 22050Hz.

But engine sounds are from TBS file from Thomas. Additional sounds made by me and I put .wav files

15
Open Panzer Help / Re: Big problem with TBS Mini
« on: April 13, 2018, 05:04:55 PM »
THX for reply Luke.

Of course I have newest TBS Flash and Mini firmware.

When I click SNOOP, I see all settings in one window. Moving sticks or toggling switches do nothing. But in RADIO section, when I click READ RADIO sticks/switches seem to work fine.

Im using Turnigy 9x transmitter with standard Flysky module. Im connecting SBUS-PPM-PWM converter to receiver. I tested tank movement with brushless motors and it was great! Servos also work good. Only one problem I have - sounds.

If I dont find solution, I must use only engine sounds and changing volume function. Or waiting for mass produced OP Sound Card.

PS. Next month I will have FlySky Taranis Radio with SBUS receiver - will see with this.

Pages: [1] 2
bomber-explosion